Star-micronics NP-225 User Manual

Spec. No D-F0301 Specifications for Kiosk module printer NP-215 NP-225 NP-325 NP-415W Revision 1.00 2000.08.01 1 edition Revision 2.0

7 2) NP-225 dimensional drawing frame groundframe ground wires L=(75)frame groundframe groundＮＰ−２２５ＲＮＰ−２２５Ｄ)(12027M3 screw holes to fix frame

8 3) NP-325 dimensional drawing frame ground wires L=(75)frame groundframe groundframe groundＮＰ−３２５ＲＮＰ−３２５Ｄ)(12027M3 screw holes to fix frame

9 4) NP-415W dimensional drawing ＮＰ−４１５ＷＤＮＰ−４１５ＷＲ19119.0149.0183.728.0112.028.0paper widthφ4.5115.582.254.3paper exit5.9 156.16.010.0 This dra

10 3. Interface specifications 3.1 Parallel interface (Centronics) 1) Data input : 8 bit parallel method(DATA 0 – DATA 7) 2) Control signals : /

11 7) Timing chart POWER T2 T3 DATA /STB BUSY T1 T4 T5 T6 /ACK T1 = 3500msec

12 3.3 Connector connections 1) J1 Power input 2) CN2 Connect to printer mechanism (head) 3) CN3 Connect to printer mechanism (motor) 4) CN4 Con

13 3. Data signal input connecter (Parallel) Printer side connecter: 57-40360 (DDK) equivalent Mating connecter: 57F-40360-20N (DDK

14 5. Data signal input connecter (Parallel/Serial) Printer side connecter: XG4C-2631 (Omron) equivalent Corresponding housing:

15 8. CN8 Connect to operation panel Printer side connector: 53047-0310(Molex) Mating connector 51021-0300(Molex) Pin# Signal name In/Output

16 4. Functions 4.1 Function setting 4.1.1 DIP switch S1 Factory setting Function ON OFF **5P **5R **5D S1-1 Interface Serial Parallel OFF ON

Read carefully Before Using the Printer Wrong handling of the printer may cause its performance declined and the product damaged. Please read the no

17 2. Start and end of self diagnostic print Set the power on while pressing the FEED switch and release the FEED switch after the printer mechanis

18 4.4 Automatic paper cut “Automatic paper cut” after paper is manually fed by pressing FEED button. If manual line feed is conducted for more than

19 5. Control commands 5.1 Control command table Control codes Functions Pages 1 HT Horizontal tab 20 2 CR Carriage return 20 3

20 5.2 Printer driver Please apply the driver stated below for using under Windows environment. Please refer to the User’s Manual for a driver.

21 7) Overall print mode setting: <<ESC ! n>> Code : [1B] h + [21] h + n * [00≤n≤FF] h Sets print mode. “n” h

22 < Reference > In the case of Font A P1=〔00〕h,P4=〔00〕h,P7=〔00〕h,P10=〔00〕h,… P2=〔00〕h,P5=〔00〕h,P8=〔0F〕h,P11=〔72〕h,… P3=〔08〕h,P6=〔F8〕h,P

23 < Reference > In the case of Font B P1=〔40〕h,P4=〔7F〕h,P7=〔41〕h,P10=〔41〕h,… P2=〔04〕h,P5=〔FC〕h,P8=〔04〕h,P11=〔04〕h,… P3=〔00〕h,P6=〔00〕h,P

24 10) Bit image mode set: << ESC * m n1 n2 Dn >> Code: [1B] h + [2A] h + m + n1 + n2 + Dn * [m = bit image mode(refer to below)] h

25 < Relationship between bit image data and printed dots > 8 dots bit image DATA

26 11) Underline set/reset : <<ESC - n>> Code : [1B] h + [2D] h + n * [00≤ n ≤02 ]h Sets and resets the underline

Table of Contents 1. Overview 1.1 Overview 1 1.2 Features 1 1.3 Configuration 2 2. Specifications 2.1 Basic specification

27 16) Bold print set/reset :<< ESC E n >> Code : [1B] h + [45] h + n * [00≤ n ≤FF] h Sets and resets

28 20) Panel switch enable/disable:<< ESC c 5 n >> Code : [1B ] h + [63] h + [35] h + n * [00≤n≤FF] h Changes t

29 Code : [1B] h + [7B] h + n * [00≤n≤FF] h Sets or resets the inverted character function * “n2 is only valid for the LSB(b0) *

30 28) Barcode print :<< GS k n Dn NUL >> Code : < 1D >h + < 6B >h + n + Dn + < 00 >h * < 00≤n≤07

31 33) Download bit image definition :<< GS * n1 n2 Dn >> Code : < 1D >h + < 2A >h + n1 + n2 + Dn * < 0

32 35) Macro definition, start and end :<< GS : >> Code : < 1D >h + < 3A >h Description : Assigns Macro defi

33 Code : < 1B >h + < 61 >h + n * < 00≤n≤02 >h Description : Aligns all data to be printed on

34 42) Compulsory eject :<<ESC r n>> Code: <1B>h + <72>h + n * < 0≤n≤1 >h * When a ticket or receipt is cramped

35 Following table shows the number of characters and input data capacity for the model 1 in version 1 to 14. Version Correction level Data code Wor

36 14 L M Q H 489 368 310 210 3908 2940 2476 1676 1167 877 738 498 707 531 447 302 486 365 307 207 299 225 189 127 1. The first code word is 4 bit

1 1. Overview 1.1 Overview The printer is categorized as following. NP - * * 5 * * 1 2 3 4 1: Pa

37 47) Reverse print set and reset :<< GS B n >> Code : < 1D > h + < 42 > h + n * < 00≤n≤FF >h Functio

38 51) Partition drive select :<< GS % n >> Code : < 1D > h + < 25 > h + n * < 01

39 6. Character code table 6.1 Domestic code table (International character set: Japan) *[SP] indicates "space". *Printer operation cann

40 6.2 Overseas code table (International character set: U.S.A) *[SP] indicates "space". *Printe

41 6.3 International character code table

42 7 Cable 7.1 B501 power cable No. PARTS NAME Q'TY MATERIAL TREATMENT 1 Mating connector 1 XHP-4 J

2 1.3 Configuration The printer consists of the following components. Product Name Description Specification Part No. Q’ty NP-215 NP-225 NP-325 NP-4

3 CODABAR (NW-7) Å Å CODE128 Å Å 2-D symology QR code Å Å Parallel Centronics Å Å 5 Interface Serial RS-232C Å Å 6 Auto-cutter 1. Cut me

4 2.2 Printing area and cutter position Cutter position (Cutting place) A TOP 0.0mm Cutter position 3.0mm Un

5 2.3 Power supply specifications 1) Power voltage : DC24V±5% 2) Current consumption *2, *3 NP-215/225 NP-325 NP415W 1 partition 2 partitio

6 2.5 Dimensions 1) NP-215 dimensional drawing frame groundframe groundframe ground wires L=(75)frame groundＮＰ−２１５ＤＮＰ−２１５Ｒpaper exit181.459 73