DOT MATRIX PRINTERDP8340R SERIES[SERIAL INTERFACE]USERS MANUAL
– 6 –3-2. PrinterFigure 3-2. Printer: Front ViewFigure 3-3. Printer: Rear View
– 7 –3-3. Part Functional Description(1) AC Power Plug Connect to an outlet of the specified voltage.(2) DC Power Outlet Supplies DC 12V power to the
– 8 –4. INSTALLATION OF INK RIBBON AND PAPER4-1. Installation of Ink Ribbon(1) Turn power off, lift the Printer Cover up and remove it.Note: Be carefu
– 9 –Figure 4-2. Installation of Ink RibbonFigure 4-3. Ribbon Spools4-2. Removal of Ink RibbonHold the spool and lift gently, rotating it until the ri
– 10 –4-3. Paper Insertion4-3-1. For Roll Paper(1) Cut the Roll Paper end straight and square. Hold the roll so that the papercomes from the bottom.(2
– 11 –4-3-2. Roll Paper Installation (When using the optional Printer Cover 8340R)When installing roll paper with the optional “Ptinter Cover 8340R”,
– 12 –4-3-3. Validation Option InstallationThe validation printing requires the optional printer cover 8340R. Refer toitem 4-3-2 for the installation.
– 13 –5. CONTROL CODESCODELF(0A)HFUNCTIONPrint and line feed instructionOUTLINEThe LF code causes the data in the line buffer to be printed,followed b
– 14 –CODESI(0F)HFUNCTIONInverted print instructionOUTLINEThis function causes the printing to be inverted. This codemust be received at the beginning
– 15 –CODEESC a n(1B)H (61)H nFUNCTIONn-line feedOUTLINEAfter printing the data in the current line, n lines are fed by thiscode. The value of n range
Federal Communications CommissionRadio Frequency InterferenceStatementThis equipment has been tested and found to comply with the limits for a Class A
– 16 –CODEESC @(1B)H (40)HFUNCTIONPrinter initializationOUTLINEAll printing conditions except ESC BEL n1 n2, the line bufferand data buffer are set to
– 17 –CODEFS(1C)HFUNCTIONTrigger peripheral unit drive (immediate)OUTLINECauses a peripheral drive pulse to be generated immediatelyCODEENQ(05)HFUNCTI
– 18 –CODEESC M(1B)H (4D)HFUNCTIONSelect 15 CPIOUTLINEThis code causes the printer to print at 15 CPI. The numberof columns per line is 44. When the p
– 19 –Character Code ListCharacter Code Function1 LF (0A)H Print and line feed instruction2 CR (0D)H Print and line feed instruction(same as LF)3 SO (
– 20 –6. GENERAL SPECIFICATIONSPrinting method Serial impact dot matrix printing,9 wiresNumber of print columns 29 columns (10CPI), 44 columns (15CPI)
– 21 –Power supply unitFour supplies available with following ratingsInput OutputAC 100 – 240 V DC 12.0 V ± 5% 47Hz – 63 Hz0.8 A Max 2.0 APaper speci
– 22 –Figure 6-1. Roll Paper and Print AreaFigure 6-2. Material to be validated and One Line Validation Printing
– 23 –Shape of AC Power plug willvary according to destinations.Figure 6-3. External Dimensions (Printer)Figure 6-4. External Dimensions (Power Supply
– 24 –7. INTERFACE FOR MODEL DP8340RM(MODULAR JACK CONNECTOR)7-1. Interface Specifications(1) Synchronization system Asynchronous(2) Baud rate 150, 30
– 25 –TYPEONLYM7-3-2. DIP-SW2Switch ON OFFFactorysetting2-1International character set :ONU.S.A FRANCE2-2 Always ON ON2-3(*2) 2-color Ribbon Monochrom
TABLE OF CONTENTS1. OUTLINE ...12. UNPACKING AND INSTALLATI
– 26 –7-4. Connectors and SignalsPin No.SignalDirection FunctionName1 GND — Shield Ground2 GND — Frame Ground3 TXD OUTThis pin carries data from the p
– 27 –TYPEONLYM7-5. Interface ConnectionsFor interface connections, refer to the instructions for interface of the hostcomputer. The following gives b
– 28 –Figure 7-6. Wiring of cable for direct connection between DP8340and IBM PC serial part7-6. Peripheral Unit Drive CircuitThe Control Board of thi
– 29 –TYPEONLYMAbsolute Ratings (Ta = 25˚C)D1 Voltage Breakdown 100VPeak Forward Current 1AFigure 7-8. Cable Connection7-6-2. Peripheral Drive Circuit
– 30 –8. INTERFACE FOR MODEL DP8340RD(D-SUB 25 PIN CONNECTOR)8-1. Interface Specifications(1) Synchronization system Asynchronous(2) Baud rate 150, 30
– 31 –TYPEONLYD8-2. Interface Circuit8-2-1. RS-232CInput (RXD, CTS)Output (DTR, FAULT, TXD, RCH, RTS)Figure 8-1. RS232-C Interface8-2-2. Current LoopI
– 32 –8-3. Setting of the DIP Switches8-3-1. DIP-SW 1Switch ON OFFFactorysetting1-1 ON1-2 Data transfer rate — see below (*1) ON1-3 ON1-4 Stop bit 1 S
– 33 –TYPEONLYD8-4. Jumper SettingThe serial interface is set to the RS-232C mode upon shipment from the factory.When using in the 20mA current loop m
– 34 –Pin No.SignalDirection FunctionName1 GND — Frame Ground2 TXD OUTThis pin carries data from the printer.(Return channel)3 RXD IN This pin carries
– 35 –TYPEONLYDFigure 8-5. D-Sub 25 Pin Connector8-6. Interface ConnectionsFor interface connections, refer to the instructions for interface of the h
8. INTERFACE FOR MODEL DP8340RD (D-SUB 25 PIN CONNECTOR)...308-1. Interface Specifications ..
– 36 –8-7. Peripheral Unit Drive CircuitThe Control Board of this unit is equipped with a circuit for driving a peripheralunit (Paper Cutter, Take-Up
– 37 –TYPEONLYDFigure 8-8. Cable Connection8-7-2. Peripheral Drive CircuitAbsolute Ratings (Ta = 25˚C)D1Voltage Breakdown 100VPeak Forward Current 1AD
– 38 –9. DATA STRUCTURE AND CONTROL9-1. DTR Mode (1 BLOCK)Controls Data Transfer by using DTR line as BUSY FLAG(a)(b) In case of Paper EmptyPaper Empt
– 39 –9-2. X-ON/X-OFF ModeThe printer transmits an X-ON (Control Code; DC1, Hexadecimal Value; 11H,)signal after power is turned on, if there is no pr
– 40 –Paper EmptyWhen the paper out detector indicates end of paper, the printer stops printing aftera maximum of two lines of printing or paper feed.
– 41 –9-3. STX-ETX ModeThe start of the STX-ETX mode should occur with a totally empty print buffer.This can be achieved by sending an ENQ code to the
– 42 –STX-ETX Mode Flow Diagram
– 43 –10. CHARACTER CODE LIST
– 45 –International Character Sets
– 1 –1. OUTLINEThe DP8340R series of serial dot matrix printers is for use in ECR, POS,electronic instruments, banking machines and computer periphera
– 46 –When printer power is supplied by the user rather than through the accessorypower source unit, please be careful of the following points.Note 1:
– 47 –VAC 14V C2 100 ~ 200µF/25VVDC 12V ZD1 VZD = 14V (1W)IAC 2 ~ 3A C3 4700 ~ 6800µF/25VC1 6800µF/25V TR1 2SD633 (TOSHIBA)Other parameters may be det
– 48 –1999.05.30Printed in Japan, 80870185ELECTRONIC PRODUCTS DIVISIONSTAR MICRONICS CO., LTD.536 Nanatsushinnya, Shimizu, Shizuoka424-0066 JapanTel:
– 2 –2. UNPACKING AND INSTALLATION2-1. UnpackingAfter opening the box, check if all necessary accessories are included.(A) Printer(B) Power Supply Uni
– 3 – 2-2. Installation of Paper Holders and Re-Roll Prevention GuardInstall the Paper Holders in the intermost holes in the rear of the printer.Figur
– 4 –Install the Re-Roll Prevention Wire in the holes of the printer cover. Twisting theWire as shown in the figure below, will make the installation
– 5 –3. PART IDENTIFICATION AND NOMENCLATURE3-1. Power Supply UnitFigure 3-1. Power Supply UnitDC Power Connector (Output)Shape of AC Power plug willv
Comments to this Manuals