Star Micronics TUP482-24 User Manual

THERMAL UNIT PRINTER MECHANISMTUP452-24TUP482-24SPECIFICATIONANDOPERATION MANUAL

– 6 – Notes) ● Use paper that is rolled inward. ● Do not affix the end of the paper to the paper roller. ● Paper jams may occur depending on the paper

– 7 – 5. PRINTER SETTINGS 5.1 Switches and Buttons The DIP switches and memory switches (EEPROM) are used to make the printer’s settings. In addi-tio

– 8 – 5.2 Setting the DIP Switches All of the DIP switches have been set to ON at the time of shipping.a) DIP switch 1 (for both RS-232C and RS-422A)

– 9 – b) DIP switch 2 (only for the RS-422A)SW 2-1 SW 2-2 SW 2-3 SW 2-4DC1, 3 disabled ON ON ON ONAddress #1 OFF ON ON ON#2 ON OFF ON ON#3 OFF OFF ON

– 10 – 5.3 Setting the EEPROM The following command from the host computer is used to make the EEPROM settings.a) EEPROM settings command<ESC>

– 11 – d) Memory switch 2N = 2n1: Always 0n2: Always 1n3: Always 0n4: Printing speed e) Memory switch 3N = 3n1: Always 0n2: Character table n3: Print

– 12 – 6. DISPLAYS AND FUNCTIONS The LEDs and RESUME button are mounted on the NEPCB. 6.1 LEDs 6.2 RESUME Button When no paper is inserted, insert mo

– 13 – 6.4 Sensor Adjusting Mode a) Reflecting sensor (black mark sensor) ● Insert the paper in front of the sensor mechanism so that a black mark is

– 14 – 6.6 Error Messages It is possible to determine the type of error occurring by observing the printing results and which LEDlights up.a) Recover

– 15 – 6.7 Near-End Sensor Position <Technical Specifications>The near-end sensors can be moved a maximum of 5 mm to the right or left by movin

NOTICE• All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’sexpress permission is forbidden.• The conte

– 16 – 7. INTERFACE Three interface types are available: parallel, serial RS-232C or serial RS-422A. Any of these interfacescan be used by installing

– 17 – RS-422AConnector Pin Assignment Item SpecificationData transfer method Asynchronous serial interfaceData transfer rate 2400, 4800, 9600, 19200S

– 18 – 7.2 Parallel Interface Connector Pin Assignment Item SpecificationMethod CentronicsData transfer rate 1000 to 6000 cpsSynchronization method E

– 19 – 8. CUTTER Notes) If the cutter is not located at the home position when an error has occurred, it can be returned to the home position by rem

– 20 – 9. PRESENTER (TUP482 series only) In order to eject the paper after it is printed and cut, a presenter can be installed on the front of the cu

– 21 – 10. CHARACTERS 10.1 Character Set ASCIIKatakana (Japanese syllabary)International character set 10.2 Characters and Sizes (Width and length of

– 22 – 11. POWER REQUIREMENTS The input voltage shall be DC 24 V ± 7% (rated 2.5 A, less than 6 A/15 sec.). The current used whensolid printing is

– 23 –54321UL1672, CSA. AWM • AWG205 : NC4 : NC3 : AC2 : NC1 : ACJST.VHR-5NPrimary power connectorStar micronics cable unit 2 × 240C BCP4(Pa

– 24 – 12. NOISE Item SpecificationMeasurement standard = ANSI 1.29 (DIN45, ISO7779)Average sound pressure at 1 m 50 dB or less

– 25 – 13. STANDARDS Safety standards1. UL (RU)2. CSARadio interference (compatible)1. FCC Class A2. CANADA DOC Class A3. VDE Class B

CONTENTS 1. GENERAL DESCRIPTION ...1 2. CONS

– 26 – 14. RELIABILITY 14.1 During operation Temperature: 5˚ ~ 40˚CHumidity: 25% RH ~ 80% RH (no condensation)Operating temperature and humidity rang

– 27 – 14.3 Allowable Static Electricity Level Notes) ● Use SLS-060P-50 (Sanken) as the power source. ● The reference data is shown in the table abo

– 28 – 14.6 Life Test MCBFNotes) ● The thermal head life given above is applicable for cases when standard paper is used. ● Printing continuously at

– 29 –15. INSTALLING THE PAPER ROLLPass the paper over the damper shaft, then pass it under the thermal head and cutter guide. Feed thepaper until the

– 30 –Carefully place the paper roll on the frame, then wind the roll to remove any slack in the paper. (Incor-rectly installing the paper roll may be

– 31 –16. INSTALLATIONInstallation procedureInstall the printer using four M4 bolts as shown in the illustration below. (Refer to the diagram of the“I

– 32 –16.1 Installation precautions1. Install the printer on a level surface. (Consult with a representative when installing the printer at anangle.)2

– 33 –External Dimensions4.8 164.273.66.1 350145.7889.2203.6164.21481038.25(PAPER WIDETH)161910.252.8

– 34 –4937579151174.619920425426616219.2120°max ø20338272.445°View A (rear surface)

– 35 –Installation Hole DimensionsUsing four M4 bolts, install the printer from the bottom as shown in the illustration below.4-M41672.4115±0.1130±0.1

– 36 –17. MaintenanceRegular maintenance is very important since minute debris of thermosensible paper sticking to theplaten may cause slipping of the

STAR MICRONICS DEUTSCHLAND GMBHWesterbachstraße 59,D-60489 Frankfurt, GermanyTel : 069-789990Fax : 069-781006STAR MICRONICS U.K. LTD.Star House, Pereg

– 1 – 1. GENERAL DESCRIPTION The TUP452-24/TUP482-24 printers are line thermal printers and are incorporated for use in variouselectronic equipment,

– 2 – 2. CONSTRUCTION 2.1 Configuration The unit printer mechanism is constructed of the following components: 2.2 Principle of Operation 2.2.1 Drive

– 3 – Exterior ViewArm NE-PCB Resume buttonInterfaceLine thermal printer PresenterCutterFrame (Inside is the main PCB and interface PCB.)

– 4 – 3. GENERAL SPECIFICATIONS Item SpecificationPrinting method Line thermal direct printingPrinting speed 50 mm/sec, 25 mm/secPrinting area 80 mm w

– 5 – 4. PAPER ROLL SPECIFICATIONS Item SpecificationPaper type Normal heat-sensitive paperPaper width 82.55 mm (3.25 in.)Paper thickness 60 to 85 µ