Star Micronics SM-T300-DB50 Manual

Mobile PrinterSM-T300 SERIES Models: SM-T300 SM-T301 SM-T302Hardware Manual

- 9 -3. Insert a new paper roll as shown.4. Tear the excess paper off using the tear bar.

- 10 -2.4. Power supply 2.4.1. Specied power supplyThe following specication is requested for Power supply. Battery Charger : DC 8.4 V/0.8 AAvoid u

- 11 -2.4.3. Recharging the battery packFor recharging the battery pack, install the battery pack in the printer.Insert the Battery Charger to the cha

- 12 -2.5. Memory switch settings1. Change the Memory switch by this operation. (Refer to Table 1). POWER button : changing Printer MODE status FEE

- 13 -u Press FEED button one time. g You will see present STOP BIT mode in the LCD. Parity Bit g Stop Bitg Press the POWER Button one time.(The st

- 14 -Printer Mode POWER Lamp(Green)ERROR Lamp(Red)OptionCommunicationPort1 1 RS-232C2 Bluetooth *Baud Rate 2 1 9600 bp2 19200 bps3 38400 bps4 57600 b

- 15 -3. Interface3.1. RS-232C15234This printer has a RS-232C interface and is connected by meansof a 5 pin mini USB socket. In the following table, t

- 16 -3.2. BluetoothCategory SpecicationBluetooth Spec. Bluetooth V2.1 / Class 2 (10 m)Frequency Range 2.4 GHz ISM BANDData Transmission Rate 57600 b

- 17 -4. Using the printer4.1. Control panelu ButtonFEED Button :When the printer is on, paper can be feed manually by pressing and holding theFEED bu

- 18 -4.2. The self testThe self test procedure will check most of the printer functions.For self test, turn on the power while holding down the FEED

Federal Communications Commission Radio Frequency Interference StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to t

- 19 - Cautions :1) Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended.2) Che

- 20 -6. SpecicationsItem SpecicationsPrint method Direct thermal line printingCharacters per line 64 cpl (MAX)Character size Eng. : 9×24 dots, 12×2

- 21 - Dimensions

SPECIAL PRODUCTS DIVISIONSTAR MICRONICS CO., LTD.536 Nanatsushinya, Shimizu-ku, Shizuoka, 424-0066 JapanTel: (int+81)-54-347-0112 Fax: (int+81)-54-

Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the Printer ● Some semiconductor devices are ea

Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes to think about where you plan to use it. Remember

Table of contents1. Introduction ...52. Setting up the printer ...

- 5 -1. IntroductionThis printer is the ideal solution for Mobile banking system , Retail,point of sales, Credit card Transaction, other traveling and

- 6 -2. Setting up the printer2.1. Printer & accessoriesYour printer box should include these items. If any items are damaged or missing, please c

- 7 -2.2. Printer features Part NamePaper coverPlatenPlaten gearPower buttonFeed buttonPower lampError lampLCDOpen switchMechanism ass’yCOMM DCCharge

- 8 -2.3. Replacing paper roll Cautions : Be sure to use paper rolls that meet the specications. Do not use paper rolls that have the paper glued to