Star Micronics TUP900 User Manual Page 23
- Page / 50
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Rev 0.01
TUP900 Series Specifications Manual
7-1
7. USAGE EXAMPLE (LAYOUT EXAMPLE)
7-1 Control Board Layout
This unit is mounted with the control board (PCB chassis) shown in Fig. 4.1.2 at the time of shipment. It is
possible, however, to change the position of the control board according to the conditions of use.
Notes 1)Changes to the control board layout are to be done by the user.
2) Be careful when laying out the cables so that wires are not broken.
Also, if necessary, use a protective tube or a wire-bundling band to protect the cable.
7-1-1 Control Board Layout 2
The control board can be arranged on the unit frame side.
Fig. 7.1.1 on the separate sheet shows an external drawing of that arrangement.
Note 1) Be careful because in this type of layout, the mechanism mounting base chassis cannot rotate.
7-1-2 Control Board Layout 3
The control board can be arranged on the unit side and the direction of the interface (optional part) can be
changed.
Fig. 7.1.2 on the separate sheet shows an external drawing of that arrangement.
7-2 High Volume Paper Roll Supply (RHU-T900, Optional Part)
Large diameter paper roll can be used by using the optional high volume paper roll supply (RHU-T900).
Fig. 7.2 on the separate sheet shows an external drawing of use of the high volume paper roll supply (RHU-
T900).
Notes 1)Be aware that the maximum paper roll outer diameter will vary according to the high volume
paper roll supply and the TUP900 Unit layout. Contact us if you have questions relating to
layout.
2) Be aware that the assembly method of the high volume paper roll supply will vary according to
the paper roll and the TUP900 layout.
3) The external drawing of Fig. 7.2 is an example of the assembly. Be aware that there are some
parts that are not included in the RHU-T900.
7-2-1 Horizontal Layout
The layout for this to place the TUP900 and high volume paper roll supply (RHU-T900) in the horizontal
direction.
Fig. 7.2.1 on the separate sheet shows the recommended layout. Note that the maximum paper roll
diameter that can be handled is φ254 mm, because of the arrangement of the apparatus in this layout.
Notes 1)Be careful when laying out the cables so that wires are not broken.
Also, if necessary, use a protective tube or a wire-bundling band to protect the cable.
2) There are cases in which, depending on the paper quality and type of paper core, the maximum
diameter φ254 paper roll cannot be transported by the printer unit. Determine your final layout
by actually trying to transport the type of paper you intend to use.
3) When using the maximum diameter paper roll of φ254, it is recommended to separate the
printer unit and high volume paper roll supply as much as is possible. Absolutely never setup
closely, as shown in Fig. 7.2.1. This can cause paper transporting problems.
7-2-2 Vertical Layout
The layout for this to place the TUP900 and high volume paper roll supply (RHU-T900) in the vertical
direction.
Fig. 7.2.2 on the separate sheet shows the recommended layout. The maximum paper roll diameter that
can be used with this layout is φ180 mm.
Notes 1)Be careful when laying out the cables so that wires are not broken.
Also, if necessary, use a protective tube or a wire-bundling band to protect the cable.
2) Be aware that the damper roller unit is different from that when mounted at the factory if you
use this layout.
- Product Specifications Manual 1
- TUP900 Series 1
- --- CONTENTS 2
- 1. GENERAL DESCRIPTION 4
- 2. PRINTER CONFIGURATION 5
- 3. BASIC SPECIFICATIONS 6
- 3-2-1 STAR Line Mode 7
- 3-2-2 STAR Page Mode 8
- 3-3 Paper Specifications 9
- 3-3-1 Thermal Paper roll 9
- Head Adjust Lever 10
- 3-4 Thermal Mechanism Module 14
- 3-4-1 Thermal Head 14
- 3-4-2 Auto-cutter 14
- 3-4-3 Paper Feed Motor 14
- 3-4-4 Sensors 14
- 3-5-1 Feed Rollers 15
- 3-5-2 Paper Feed Motor 15
- 3-5-3 Sensors 15
- 3-5 Presenter Module 15
- 3-6 Paper Roll Supply Module 16
- 3-6-1 Paper Roll Holder 16
- 3-6-2 Near-end Sensor 16
- 3-7-2 Thermal Head 17
- 3-7-3 Auto-cutter 17
- 3-7-4 Presenter Module 17
- 4. EXTERNAL SPECIFICATIONS 18
- Rev 0.01 19
- 5. ENVIRONMENT SPECIFICATIONS 20
- 6. SAFETY 22
- TUP900 Se 25
- E-E Section 26
- Fig. 7.2.1 Horizontal Layout 27
- Fig. 7.2.2 Vertical Layout 28
- 8-1 Mounting the Units 29
- 8-4-1 Using the Spring Base 32
- Fig. 8.4.1.C 33
- Fig. 8.4.1.A 33
- Fig. 8.5.1.A 38
- Fig. 8.5.2.A 39
- Fig. 8.5.2.B 39
- 9. HANDLING THE PRINTER UNIT 40
- 9-4 How to Set the Paper roll 42
- Fig. 9.4.C 44
- Fig.9.4.E 45
- 9-5 Performing Maintenance 46
- Release lever 47
- Lock lever 47
- 1) the DIP Switches (DIPSW) 48
- 2) Memory Switches 48
- Distributed by 50
Related products and manuals for Label printers Star Micronics TUP900
Label printers Star Micronics NP-IO User Manual
(100 pages)
(100 pages)
Label printers Star Micronics SG-10 User Manual
(128 pages)
(128 pages)
Label printers Star Micronics TSP800 User Manual
(115 pages)
(115 pages)
Label printers Star Micronics NR-15 User Manual
(128 pages)
(128 pages)
Label printers Star Micronics NB-15 User Manual
(114 pages)
(114 pages)
Label printers Star Micronics TSP600 User Manual
(113 pages)
(113 pages)
Label printers Star Micronics NX-10 User Manual
(129 pages)
(129 pages)
(100 pages)© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals