Star Micronics TSP654II-WebPRNT-2 Manual

THERMAL PRINTERTSP650II SERIESHardware Manual

- 6 -Ethernet cableIFBD-HE073-2-4. Ethernet CableTo connect the cable, follow the procedure given below.(1) Make sure that the AC adapter’s power cor

- 7 -3-3. Connecting the AC AdapterNote: Before connecting or disconnecting the AC adapter, make sure that the printer and all the devices connected

- 8 -Power switch3-4. Turning the Power OnConnect the power cord according to the procedure in section 3-3, “Connecting the AC Adapter”. Turn on the

- 9 -Cover open leverPaper roll3-6. Loading a Paper RollUse a paper roll that complies with the printer specications. (1) Push the cover open lever

- 10 -3-6-1. Compliant Paper Roll SpecicationsPaper thickness53 μm to 85 μmPaper width79.5 ± 0.5 mm57.5 ± 0.5 mmExternal dimensions •Rolldiameter

- 11 -Paper roll guideA3-6-2. Changing the Paper WidthWhen using 57.5 mm width paper rolls, attach the supplied paper roll guide to the printer. When

- 12 -PAIRRSTPAIRRSTPAIRRSTPAIR buttonPAIR buttonRST buttonLED3-7. Bluetooth Settings (For Bluetooth Interface Models only)(2) Pairing will be possi

- 13 -ERRORFEEDPOWERTSP6503-7-2. Pairing using PIN code Enter the following information in the master device if it does not support SSP, or when othe

- 14 -Auto Connection ON Auto Connection OFFReconnecting without changing the parent deviceAfter the printer is turned on, it automatically connects t

- 15 -< Current Setting >Auto Connection : OFFTo enable this setting, turnPrinter Power OFF and turn ON.PAIRRSTPAIRRSTRST button3-7-4. Setting

Federal Communications CommissionRadio Frequency InterferenceStatementis device complies with Part 15 of the FCC Rules. Operation is subject to the f

- 16 -PAIRRSTPAIRRST“Made for iPod” ,“Made for iPhone” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically

- 17 -Caution Symbolese symbols are located near the thermal print head.Because the thermal print head is hot immediately aer printing, do not touch

- 18 -l Do not open the printer covers while the printer is printing or cutting.l Do not pull out paper when the printer cover is closed.l If liqui

- 19 -2∼3mm4. Attaching the Accessoriese following accessories are necessary when mounting the printer to a wall.• Holder plate and two angeless scr

- 20 -(3) Push the cover open lever, and open the printer cover.(4) Insert the roll paper as shown.Precautions regarding installation　 CAUTIONThis

- 21 -4-2. Attaching the Rubber Feet(1) Ensure that any soiling has been completely wiped o before attaching the rubber feet.(2) Attach the four r

- 22 -5. Adjusting the Near-end SensorUse the following procedure to adjust the near-end sensor so it is compatible with the size of paper roll you ar

- 23 - 6. Error Indicators6-1. Recoverable errorsCheck the recovery conditions. e printer can be recovered while maintaining its current status.Erro

- 24 - 7. Preventing and Removing Paper JamsThermal head7-1. Preventing Paper Jamsl To avoid paper jams and other problems, feed the paper at least

- 25 -Home positionKnobDrive knifeDrive knifeNGOKHome positionFront coverCutter unitPrinter cover7-3. Releasing the Cutter LockIf the auto cutter loc

Trademark acknowledgmentsTSP650II : Star Micronics Co., Ltd.Notice• All rights reserved. Reproduction of any part of this manual in any form whatsoe

- 26 -8. MaintenanceThermal headRubber rollerPaper holderAccumulation of paper dust and dirt may cause the printer to not print portions of characters

English: Hereby, STAR MICRONICS CO.,LTD. declares that this Wireless Device is in compliance with the essential requirements and other relevant provis

Application of Council Directive(s)1999/5/EC of 9 Mar 19992004/108/EC of 15 Dec 20042006/95/EC of 12 Dec 20062011/65/EU of 8 Jun 2011Standard(s) to wh

http://www.starmicronics.com/support/

TABLE OF CONTENTS 1. Unpacking and Installation ... 11-1. Unpacking ...

- 1 - 1. Unpacking and Installation* Accessories vary depending on the model and the region where the printer was purchased.Paper rollPrinterHolding

- 2 -ERRORFEEDPOWERTSP650 2. Parts Identication and NomenclatureControl panelFeatures lamps that indicate printer status and a button for operating t

- 3 - 3. Setup3-1. Connecting the Interface Cable to the PC3-1-1. Parallel CableConnect the parallel cable to a parallel port on your PC.3-1-2. RS-

- 4 -Parallel interface cableFerrite coreInterface cable5 cm(maximum)FastenerPull and cut3-2. Connecting the Interface Cable to the PrinterPrinter cab

- 5 -RS-232C interface cableUSB cableCable hook4 cm (maximum)3-2-2. RS-232C Interface Cable(1) Make sure that the AC adapter’s power cord is not con