Star Micronics NX-2420 User Manual Page 32
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
24
ON LINE button
The ( ON LINE ) button sets the printer on-line and off-line. The status
changes each time you press the button.
When the printer is on-line, it can receive and print data from the computer.
When the printer is off-line, it stops printing and sends the computer a signal
indicating that it cannot accept data.
The printer powers up in the on-line status if paper is loaded, If paper is not
loaded, the printer powers up off-line with the POWER indicator flashing.
When you load paper, the POWER indicator stops flashing, and the printer
goes on-line.
You will want to press the ( ON LINE
) button:
l Before and after any other panel operation
The other panel buttons operate only in the off-line state. Press the
( ON LINE > button to go off-line. After performing the panel
operation(s), press the ( ON LINE ) button again to go back on-line.
l To pause during printing
If you press the ( ON LINE ) button during printing, the printer stops
printing and goes off-line, allowing you to check the printout or change
a control panel setting. Printing resumes when you press the (
ON LINE )
button again to go back on-line.
l To cut fanfold forms at the end of printing
When using fanfold forms, you can hold the ( ON LINE
> button down
for one second. In addition to going off-line, the printer also feeds the
paper forward approximately two inches. This allows you to cut it off just
-
below the last line printed.
When you press the ( ON LINE ) button again to go back on-line, the
paper feeds backward stopping where you left off.
NOTE:This function is valid only when the buffer is empty.
PAPER FEED button
If you press this button while off-line, the paper will feed forward. If you
hold the button down, the printer will perform consecutive line feeds.
- NX-2420 1
- HOW TO USE THIS MANUAL 3
- FEATURES OF THE PRINTER 5
- TABLE OF CONTENTS 6
- Chapter 3 DEFAULT SETTINGS 7
- Chapter 8 SPECIFICATIONS 8
- Chapter 9 CHARACTER SETS 8
- COMMAND SUMMARY 8
- Chapter 1 9
- UNPACKING AND INSPECTION 10
- /den tifying printer parts 11
- Mounting the platen knob 12
- Automatic loading 18
- ON LINE 19
- Manual loading 20
- Paper parking 25
- Paper unparking 26
- LOADING MULTI-PART FORMS 27
- Adjustment lever 28
- Chapter 2 31
- ON LINE button 32
- PAPER FEED button 32
- SET/EJECT/PARK button 33
- PITCH button 33
- FONT button 34
- Short test mode 35
- Long test mode 36
- Print area test mode 37
- Stay in Panel Pitch 37
- Stay in Panel Font 37
- Hexadecimal dump 38
- Form feed 40
- Top of form 40
- Forward micro-feed 41
- Reverse micro-feed 41
- ON LINE > button 42
- Selecting the print color 43
- Store Macro Definition 43
- IBM mode, and vice versa 44
- Chapter 3 45
- 1 OCPI LQ 48
- “DRAFT” and “DRAFT COND” 51
- /RAFT cotm 0 : 52
- Chapter 4 53
- PRINTER CONTROL COMMANDS 53
- FONT CONTROL COMMANDS 54
- Select L Q characters 55
- Select LQ pica characters 55
- Select LQ elite characters 55
- Select LQ font 56
- Select font 56
- Select italic characters 57
- Select upright characters 57
- Emphasized printing 57
- Cancel emphasized printing 57
- Double-s trike printing 57
- Start underlining 58
- Stop underlining 58
- S tarf 0 verlining 58
- Stop 0 vet-lining 58
- Select score 59
- Select ornament character 59
- Superscript 59
- Subscript 60
- Select IBM character set 60
- Select character set #I 61
- Select character set #2 61
- Select IBM code page 62
- Select slash zero 63
- Select normal zero 63
- Pica pitch 63
- Elite pitch 63
- Semi-condensed pitch 64
- Condensed printing 64
- Cancel condensed printing 64
- Expanded printing 64
- Cancel expanded printing 64
- Select character width 65
- Select fixed spacing 66
- Select master print mode 66
- Increase character spacing 66
- Select character size 67
- Return to normal height 68
- Execute <ES& “cA” 71
- Line feed 71
- Reverse line feed 71
- Select forward feed mode 71
- Select reverse feed mode 71
- Feed paper n lines 72
- Set page length to n lines 72
- Set bottom margin 73
- Cancel bottom margin 73
- Form feed 73
- Disable paper-out detector 74
- Enable paper-out detector 74
- Set vertical tab stops 74
- Vertical tab 75
- Set left margin 76
- Set right margin 76
- Backspace 77
- Set left and right margins 77
- Carriage return 77
- Set automatic line feed 77
- Cancel automa tic line feed 77
- Left justify 78
- Center text 78
- Right justify 78
- Full justify 78
- Set horizontal tab stops 79
- Reset all tab stops 79
- Horizontal tab 79
- Relative horizontal tab 80
- GRAPHICS COMMANDS 81
- Se/ect graphics mode 82
- Seiecf graphics mode 83
- Convert graphics density 83
- Define download characters 84
- 27 56 0 n 0 lB3AOO nOO 86
- 27 37 49 IB 25 31 86
- 27 37 1 1B 25 01 86
- Select ROM character set 88
- I 18 I 90
- Stop printing 91
- Bidirectional printing 91
- Unidirectional printing 91
- Manual feed 92
- Auto feed 92
- Eject paper from ASF 92
- Reset printer 92
Related products and manuals for Print & Scan Star Micronics NX-2420
Print & Scan Star Micronics TSP552II User Manual
(113 pages)
(113 pages)
Print & Scan Star Micronics TUP400 User Manual
(103 pages)
(103 pages)
Print & Scan Star Micronics LC-15 User Manual
(130 pages)
(130 pages)
Print & Scan Star Micronics SP2000 User Manual
(170 pages)
(170 pages)
© 2020, manymanuals.com. All rights reserved. | 1.932 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals