Hardware Manual Model: TSP143IIU
– 7 –3-3. Connecting to a Peripheral UnitYou can connect a peripheral unit to the printer using a modular plug. e following describes how to install
– 8 –3-4. Turning Power On and Power OImportant:is printer is not equipped with a power switch.1) e following four conditions are necessary to tur
– 9 –CAUTION• Depending on the computer that is connected to the printer, the printer may not enter the system o mode even if the computer is turned
– 10 –Cover open lever1) Push the cover open lever, and open the printer cover.2) While observing the direction of the roll, set the paper roll into
– 11 –3-5-2. Using 57.5 mm Width Paper RollWhen using a paper roll with 57.5 mm width, install the supplied paper guide on the printer.To change the e
– 12 –Caution Symbolese labels are located near the thermal print head.Because the thermal print head is hot immediately after printing, do not touch
– 13 –CAUTION1) Do not operate the cover open lever while pressing on the printer cover with your hand. 2) Do not push the cover open lever and open
– 14 –4. Attaching the Accessoriese following accessories are necessary when mounting the printer to a wall.• Upper guide and two anged screws• Hold
– 15 –4-2. Attaching the Holder Plate• e holder plate is attached to the printer using the included screws and is hooked onto screws that are insta
– 16 –(2) Position the printer over the screws, etc., on the wall and then slide it downward to set it in place. Aer setting the printer in pl
Federal Communications CommissionRadio Frequency InterferenceStatementis device complies with Part 15 of the FCC Rules. Operation is subject to the f
– 17 –4-3. Attaching the Rubber Feet(1) Attach the four rubber feet in the posi-tions shown in the gure. Ensure that any soiling has b
– 18 –5. Thermal Roll Paper SpecicationWhen consumable parts have run out, use those specied below.5-1. Compliant Paper Roll Specicationsickness
– 19 –6. Control Panel and Other Functions6-1. Control Panel1 POWER lamp (Green LED)3 FEED button2 ERROR lamp (Red LED)6-2. Lamp Indicator1) Printe
– 20 –2) Automatically recoverable errorsError Description POWER Lamp ERROR Lamp Recovery ConditionsCover open error On On Automatically recovered a
– 21 –6-3. Self-PrintingTest Printing1) Make sure that the computer is turned on.2) Make sure that the printer’s power cord is plugged into an AC out
– 22 –7. Preventing and Clearing Paper Jams7-1. Preventing Paper Jamse paper should not be touched during ejection and before it is cut.Pressing or
– 23 –Thermal headCaution Symbolese labels are located near the thermal print head.Because the thermal print head is hot immediately after printing,
– 24 –7-3. Releasing a Locked Cutter If the auto cutter locks up, disconnect the USB cable, and unplug the power cord to turn the printer o. en rec
– 25 –(4) Insert a Philips screwdriver into the manual operation hole on the side of the cutter, and turn it in the direction of the arrow shown on t
– 26 –Thermal headRubber roller8. Periodical CleaningPrinted characters may become partially unclear due to accumulated paper dust and dirt. To preven
Please access the following URLhttp://www.starmicronics.com/support/for the latest revision of the manual.TABLE OF CONTENTS1. Unpacking and Installati
http://www.starmicronics.com/support/
– 1 –1. Unpacking and Installation1-1. UnpackingAer unpacking the unit, check that all the necessary accessories are included in the package.Fig. 1-
– 2 –1-2. Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes to think about where you plan
– 3 –1-3. NomenclatureDKO lCover open lever Push this lever in the direction of the arrow to open the printer cover.Control panelFeatures LED indi
– 4 –2. Product Features2-1. Product Features• is printer is not equipped with a power switch. e printer turns on when the computer, which the prin
– 5 –3. Setup3-1. Connecting the Power Cord(1) Check the label on the back or bottom of the printer to make sure its voltage matches that of the AC
– 6 –3-2. Connecting the USB Cable to the PrinterPass the cable through the cable support as shown. en, connect the USB interface cable to the print
Comments to this Manuals