Mobile PrinterSM-T300I SERIES Hardware Manual
- 3 -1.2 External Appearance and Part Names※Remove the lms if you do not need them.Platen GearPlatenPrinter CoverCover Open SwitchThermal HeadMechan
- 4 -2. Setup2.1 Battery Pack2.1.1 Inserting into the Printer1. Make sure that the printer has been turned o before you insert or remove the batte
- 5 -2.1.2 Charging the BatteryInsert the battery pack into the printer to charge it.Insert the battery charger cable into the printer’s power inlet
- 6 -< For U.S.A. and Canada >Lithium-Ionbatteriesarerecyclable.Youcanhelppreserveourenvironmentbyre-turning your used rechargeable b
- 7 -2.2 Bluetooth Settings2.2.1 connection1. Press and hold POWER for approx. 3 seconds, and printer is turned on. Then, it is ready to pair with
- 8 -2.2.2 Auto Connection Function (only for iOS*1)When the Bluetooth connection with your iOS device(*2 is disconnected, it is required to establis
- 9 -2.3 Loading PaperRefer to chapter 4, “Paper” (p. 19), to select roll paper that conforms to the specications.1. Turn on the printer.2. Put yo
- 10 -CAUTIONWhen the paper is jammed, be sure to open the printer cover before removing the jammed paper.Do not under any circumstances try to pull o
- 11 -2.4 Memory Switch SettingsChange the Memory switch by following operations. (Refer to page 13 “Memory Switch Set-ting Table”).1. Press and hol
- 12 - * Example:When you want to change the settings of the printer mode as shown below,<Before> Bluetooth/9600BPS/8DATABIT/NOPARI
<USA model>Federal Communications Commission Radio Frequency Interference StatementThis device complies with Part 15 of the FCC Rules. Operatio
- 13 -Memory Switch Setting TablePrinter Mode SettingDisplay1 Communication Port v1)RS-232C UART ModeBluetooth Bluetooth ModeBluetooth(iOS) * Blueto
- 14 -v1) Communication modeIt is possible to change the communication mode setting between Bluetooth and serial. Please see below for details to sel
- 15 -2.5 Belt Clip2.5.1 Attaching to the PrinterFollow the procedure below to attach the belt clip to the printer.1. Make sure that you are attach
- 16 -3.1.1 Button1) POWER Button :1 Pressing and holding the POWER button for 3 seconds or more will turn the power on or o.2 Pressing both the PO
- 17 -3.2 Self TestYoucanuseaselftesttochecktheprinter’ssettings.Before you start the self test, make sure that roll paper has been properl
- 18 -3.3 Instruction for Auto Power Down(Sleep) ModeThe printer in the Power Down(Sleep) Mode will recover to the Print Ready Mode when receiv-ing c
- 19 -4.2 Recommended PaperManufacturer Product NameMitsubishi Paper Mills Limited P220AGOji Paper Co., Ltd. PD450APPLETON Alpha 800-2.4KANZAKI (Oji
- 20 -5. General SpecicationsItem SpecicationsPrinting method Direct line thermal printingCharacters per line Maximum 64 cplCharacter sizeAlphanumer
- 21 -n DimensionsExternal Dimensions : 120 mm (W) × 130.5 mm (D) × 58.3 mm (H) <Model without Card Reader> 120 mm (W) × 132.2 mm (D) × 58
Application of Council Directive(s)1999/5/EC of 9 Mar. 19992011/65/EU of 8 Jun 2011Standard(s) to which Conformity is Declared RADIO :EN 300 328 V1.7.
Trademark acknowledgmentsSM-T300I: Star Micronics Co., Ltd.Notice• Allrightsreserved.Reproductionofanypartofthismanualinanyformwhatsoeve
URL: http://www.starmicronics.com/support/Rev. 1.2
Caution SymbolThis symbol is placed near the thermal head to indicate that it may be hot.Never touch the thermal head immediately after the printer ha
n Using the Printer P Some semiconductors can be damaged by static electricity. Be sure to turn o the printer when inserting or removing the battery
n Operating Environment for the PrinterBefore actually unpacking the printer, you should take a few minutes to think about where you plan to use it. R
Table of Contents1. Product Overview ... 11.1 Printer & Acces
- 1 -iPod, iPhone and iPad compatibility listMade for • iPod touch (4th generation) • iPhone 4S • iPhone 4 • iPhone 3GS• iPad (3rd gene
- 2 -Shoulder Strap1.1 Printer & AccessoriesThe printer is packaged with the following accessories.If any of these accessories is broken or missi
Comments to this Manuals